OLED Development Kit: Difference between revisions
From olighker
More actions
No edit summary |
No edit summary |
||
| Line 8: | Line 8: | ||
|intro=128*64 SSD1309 24pin | |intro=128*64 SSD1309 24pin | ||
|highlights=''2.42" 128x''64 OLED Screen, Multi-interface, 24Pin Soldering Flex Cable, Compatible with ESP32 / Arduino. | |highlights=''2.42" 128x''64 OLED Screen, Multi-interface, 24Pin Soldering Flex Cable, Compatible with ESP32 / Arduino. | ||
|specs={{{!}} class="wikitable" | |||
{{!}}+ | |||
!Item | |||
!Specification | |||
{{!}}- | |||
!Size | |||
!2.42 inch OLED Screen | |||
{{!}}- | |||
!Resolution | |||
!128*64 | |||
{{!}}- | |||
!Interface Type | |||
!8-bit 68**/80** Parallel, SPI, IIC | |||
{{!}}- | |||
!Controller IC | |||
!SSD1309 | |||
{{!}}- | |||
!Display Color | |||
!Blue | |||
{{!}}- | |||
!Active Area | |||
!55.01 × 27.49 (mm) | |||
{{!}}- | |||
!Panel Dimension | |||
!60.50 × 37.00 × 2.00 (mm) | |||
{{!}}- | |||
!Pixel Pitch | |||
!0.43 × 0.43 (mm) | |||
{{!}}- | |||
{{!}}Pixel Size | |||
{{!}}0.40 × 0.40 (mm) | |||
{{!}}- | |||
{{!}}Flex Cable Length | |||
{{!}}36 (mm) | |||
{{!}}- | |||
{{!}}Pin Count | |||
{{!}}24pin (0.5mm Top Contact Type) | |||
{{!}}- | |||
{{!}}Viewing Angle | |||
{{!}}Full Viewing Angle | |||
{{!}}- | |||
{{!}}Operating Temperature | |||
{{!}} -40 ~ 70℃ | |||
{{!}}} | |||
|hardware=== <span style="color: rgb(52, 176, 176);">1.Hardware Wiring</span> == | |hardware=== <span style="color: rgb(52, 176, 176);">1.Hardware Wiring</span> == | ||
2.42" OLED (SSD1309, IIC Interface) ↔ Arduino Board | 2.42" OLED (SSD1309, IIC Interface) ↔ Arduino Board | ||
Revision as of 23:29, 16 September 2026
OLED Display
2.42-inch OLED
Published
128*64 SSD1309 24pin
Introduction
2.42" 128x64 OLED Screen, Multi-interface, 24Pin Soldering Flex Cable, Compatible with ESP32 / Arduino.
Specifications
| Item | Specification |
|---|---|
| Size | 2.42 inch OLED Screen |
| Resolution | 128*64 |
| Interface Type | 8-bit 68**/80** Parallel, SPI, IIC |
| Controller IC | SSD1309 |
| Display Color | Blue |
| Active Area | 55.01 × 27.49 (mm) |
| Panel Dimension | 60.50 × 37.00 × 2.00 (mm) |
| Pixel Pitch | 0.43 × 0.43 (mm) |
| Pixel Size | 0.40 × 0.40 (mm) |
| Flex Cable Length | 36 (mm) |
| Pin Count | 24pin (0.5mm Top Contact Type) |
| Viewing Angle | Full Viewing Angle |
| Operating Temperature | -40 ~ 70℃ |
Hardware
1.Hardware Wiring
2.42" OLED (SSD1309, IIC Interface) ↔ Arduino Board
You need to use the OLED 24P Shield adapter board, together with an Arduino-compatible mainboard. You can freely choose either ESP8266 Arduino Board or ESP32 Arduino Board.
2.Compilation & Upload
Open the sample code, compile it, upload the code, and perform the final test.
Size
- Connect power and the I2C bus.
- Scan and confirm the device address.
- Load the driver matching the resolution.
- Draw text and graphics to verify orientation.
FAQ
- What if the address cannot be scanned?
- Check power, ground, SCL/SDA reversal, and pull-up resistors.
- What if the display content is misaligned?
- Confirm controller model, resolution, and page addressing mode.
Downloads
暂无Published资源，管理员可在产品表单中添加下载文件。